Ukrainian Special Purpose Tactical Pants Mabuta Mk-2 Camouflage MM-14 UA-Digital Brand - P1G-TAC® FIELD SUMMER PANTS "MABUTA MK-2" (HOT WEATHER FIELD PANTS) 8 pockets elastic inserts at waist and knees belt width up to 5.5 cm can be used bottom leg cuffs lined for extra durability patch pockets close with English buttons 4 D-rings for attaching additional equipment empty patch pockets fit snugly around the leg wide and rigid waistband with cushioning insert pant leg width adjustable with hook-and-loop fastener wide hook-and-loop fastener with individual adjustability back hip pockets can be used as empty magazine pouches removable knee pads that can be adjusted horizontally and vertically duplicating insert in front pockets for increased wearability when carrying clip-on gear fabric - Rip-stop Prof-it-On (60% Cotton, 40% Polyester) The history of the Mabuta suit dates back to Soviet times. It's a suit for hot climates that was popular among special forces, reconnaissance and paratroopers. In 2013, the P1G-TAC brand created a modern version called MABUTA Mk-2. The updated version retained all the best qualities of its predecessor and was supplemented with modern material and improved design solutions based on the trends of the 21st century field uniform. MABUTA Mk-2 pants are designed with eight pockets: two front slash pockets, two front hip pockets with flaps, two front hip pockets with hook-and-loop flaps, and two hip pockets on the back with flaps. Both pairs of pockets on the hip are closed with English buttons, which are easy to open when wearing gloves. Also thanks to this method of fastening the buttons increases the durability and decreases the chances of tearing them off. Rear hip pockets are equipped with an elastic band with a stopper in order to adjust the size of the entrance hole in the pocket and use them instead of magazine drop. The pockets have special creases so that the empty pocket fits snugly on the surface of the pants and evenly decomposes to accommodate everything you need. The waist area is wide and rigid with an internal cushioning insert. Therefore, a tight fit of the pants and good sweat absorption is ensured. The rear part of the waist zone has an elastic nylon insert, which allows you to maintain freedom of movement even when the waistband is rigidly fixed. Also this area is supplemented with wide waist slits, which allows the use of a wide waistband. They are equipped with four YKK D-rings for attaching additional gear. For freedom of movement in the knee area, it has an elastic nylon insert. To protect the knee joints in this model, there are integrated kneepads that can be removed if necessary. They are made of a combination of plastic uppers and soft cushioning. The fit of the kneepads can be adjusted: in height from the front pockets on the thigh, and in bounce using the elastic bands on the back of the kneepad. Bottom of the leg on the inner side is reinforced with duplicating pads. This area is also equipped with hook-and-loop cuffs to prevent dirt and sand from getting inside the shoes.

The lightweight and ergonomic warbelt will allow you to carry even more gear without sacrificing mobility and comfort. Its main function is to transfer the weight of the equipment to the hips and legs, unlike classic RPS, which load the shoulders and lower back muscles. The design of the warbelt was developed taking into account the features of modern warfare, so it is easy and comfortable to run, crawl and move in transport, including cars. After all, it is often necessary to use all the means available at hand to perform combat tasks. In the middle of the warbelt, a belt made of solid polyamide sling is stretched, which, if necessary, can be used as a standard military belt. Size adjustment is thanks to a strong fastex made of acetal. Also, the warbelt is equipped with attachment points for shoulder straps, which turns it into a full-fledged RPS.

Backpack for plate carrier is designed taking into account the needs of the military, police and operators of special units. This bag model is designed to carry a small set of extras, extra BC, water, etc. The main compartment of the bag opens completely and has an internal organizer system. It also has a separate pocket that allows you to conveniently separate things from other gear. On the front of the backpack there is a flat pocket with a vertical loading for the hydraulic system to the full height of the bag. There is also a Velcro panel for placing IDs and other accessories. The functional front part is equipped with a MOLLE panel for additional summaries. The Assault Pack can be attached to any MOLLE compatible gear such as plate carriers, backpacks, etc. For this, there are four MOLLE straps on the back of the bag. This design ensures the maximum fit of the bottom to the back and does not increase the silhouette.