The new model is a set of automatic LED backlight stairs allows you to connect up to 26 steps of stairs.
Now you can use as a pyroelectric infrared sensors and ultrasonic rangefinders, in any combination, as you need.
The kit includes:
1. Automatic illumination controller SmartStarway SS-26 - 1 pcs.
2 The pyroelectric motion sensor PIR-SR501-1 - 2 pcs.
3. Light sensor. - 1 pcs.
4. Box and user manual. - 1 pcs
The controller for an automatic lighting of stairways by means of low-power LED light sources. One controller is able to provide coverage of from 4 to 26 stages. The controllers have the ability to enable consistent, which allows to increase the possible number of steps almost to infinity. The system provides a flexible configuration for any customer requirements. The controller can be used in conjunction with a light sensor, or without it, with passage switches simple pyroelectric (infrared) and digital sensors to ensure smooth movement series circuit when the signal from the sensors in the direction of movement of people included on the ladder. Or with dual sensors Veda count of persons on the stairs, considering the number of people entered and emerged, providing a staircase lighting as long as people are on the steps. The controller has a customizable interface and intuitive settings available. Easy to install.
The controller is made in a plastic case that can be mounted on DIN-rail or attached to the surface by means of screws or screws. (see photo)
User Guide in English can be downloaded here shop.xopc.net.ua/files/pasport_ss26_eng.pdf
The main advantages of the system.
1. Small body size and its convenient mounting on DIN-rail in standard
wiring embedded and external boxes.
2. Digital motion sensors in the standard wiring boxes.
3. External light sensor allows you to choose the installation location with a constant light level is not dependent on or off lighting stairs or more light sources.
4. Easy and intuitive customization system.
5. Adjustable "light duty" first and last steps of a ladder.
6. Ability to connect through passage switch for lighting control at any time, regardless of the lighting conditions.
7. Low power consumption.
8. Long service life of LED light sources (tape or spotlights).
9. Easy installation and operation.
The algorithm of the system
When motion is detected the backlight in the direction of human movement. Those. triggered by the sensor to the opposite. If in the process of moving when not fully backlight load sensor on the opposite side - is turned counter lights in the direction of movement of another person logged on to the ladder. After the staircase turns completely switched standby timer (specified in the Settings menu to claim 5), after which the backlight turns off smoothly stages in the same order.
Using a light sensor.
The controller can be used as a light sensor and without it. When connected to the controller light sensor should activate its use (claim 1. Setting) or deactivated when not using the sensor. The sensor should be installed in such a place that it would not be reached by light from indoor lighting and the lighting levels themselves. Digital sensor delivers a logic controller port 0 when the lighting is not sufficient or logical unit if the light level is less than the set limit. When the lighting is activated by light duty first and last stages and the controller is allowed to turn on the backlight levels for the signals from motion sensors depending on the selected algorithm (see. Above). When driving on the stairs when the backlight is switched on or suddenly steps onto the sensor light gets brighter light controller activation threshold - the staircase lights and duty levels off and the controller will go into standby mode. Job motion sensors and processing of people on the stairs counters maintained even when the lights on the signal light sensor is not implemented.
Using the motion sensor.
The controller allows you to connect any motion sensors, which you need. It can be both pyroelectric and ultrasound sensors. You can connect both sensors of the same type or a single pyroelectric and ultrasound in any combination. The controller automatically performs a self-test when you turn on and determine what type of sensor is connected to it. The default factory setting for the width of the stairs of the ultrasonic sensor is set equal to 1 meter. The movement will be determined if the distance to the obstacle is reduced by more than 10 cm. Measurements of ultrasonic sensors are carried out by calculating the average value of 5 measurements, that virtually eliminates false positives when using ultrasonic sensors. If necessary, you can easily change the width of the stairs through the controller setup menu in step 7. Details can be found in the user manual URL: shop.xopc.net.ua/files/pasport_ss26_eng.pdf
Note! Ultrasonic sensors have certain technological shortcomings. Their principle of operation is based on the reflected high frequency sound. Therefore, ultrasonic sensors can not detect an obstacle if a person is dressed in a sound-absorbing clothes and have a certain delay in the work, because return time of the sound wave takes from 50 to 500 Milis
We recommend ipolzovat pyroelectric sensors, whenever possible. The use of ultrasonic sensors is justified only when the staircase has no handrail or banister is delicate and next to the stairs is communicating zone through which people move and it may cause false triggering of illumination ladder pyroelectric sensors.
1. The number of channels (the number of connected steps) minimum - 4 pcs.
maximum - 26 pcs.
2. DC supply voltage of 12 V.
3. The maximum current load on channel 1 (step 1) 0.4A (4,8W)
4. Sensing elements
digital photo sensor
5. Power Digital Sensor Inputs: DC 5V
6. Protection Ip22
7. Ambient temperature -5 ... + 50`C
8. Controller Case Dimensions 115x90x41 mm
9. Controller Power Consumption
standby time (up to): 0,3W.
10. Power consumption controller under load (max): 3,5W.
11. The maximum total allowable load capacity (max): 125 watts.